Stainless Steel pipe - 150mm (6")

6" / 150mm diameter connecting pipe - 1 mm stainless steel flue. A single wall flue system manufactured in 316 grade stainless steel, 1mm thick. 

Pipes

Product Code: 1-155-1000

Fixed length pipe. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £93.84
Our Price: £46.92

Product Code: 1-155-1000D

Fixed length pipe with access door for sweeping. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £130.30
Our Price: £68.41

Product Code: 1-155-150

Fixed length pipe. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £22.95
Our Price: £11.94

Product Code: 1-155-175TEL

175mm adjustable telescopic length - adjusts between 175mm and 300mm. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £53.12
Our Price: £26.56

Product Code: 1-155-300

Fixed length pipe. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £35.85
Our Price: £17.92

Product Code: 1-155-300D

Fixed length pipe with access door for sweeping. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £72.31
Our Price: £37.96

Product Code: 1-155-300TEL

300mm adjustable telescopic length - adjusts between 300mm and 550mm. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £94.92
Our Price: £47.46

Product Code: 1-155-500

Fixed length pipe. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £52.99
Our Price: £26.49

Product Code: 1-155-500D

Fixed length pipe with access door for sweeping. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £89.48
Our Price: £46.98

Product Code: 1-155-500TEL

500mm adjustable telescopic length - adjusts between 500mm and 950mm. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £106.72
Our Price: £53.36

Elbows/tees

Product Code: 1-155-15

Fixed elbow. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £40.52
Our Price: £23.91

Product Code: 1-155-30

Fixed elbow. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £40.52
Our Price: £23.91

Product Code: 1-155-45

Fixed elbow. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £40.52
Our Price: £23.91

Product Code: 1-155-45D

Fixed elbow. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £95.00
Our Price: £56.05

Product Code: 1-155-45T

Tee and drain cap. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £118.03
Our Price: £61.97

Product Code: 1-155-90

Fixed elbow. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £69.48
Our Price: £38.22

Product Code: 1-155-90T

Tee and drain cap. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £106.45
Our Price: £55.89

Adapters

Product Code: 1-155-ADP

Conical increaser, increases diameter from 150mm (6 inch) to 175mm (7 inch)
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £66.01
Our Price: £39.61

Supports

Product Code: 1-155-ABRK

Adjustable wall bracket provides lateral stability - length can be adjusted from 50 to 300mm. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £28.01
Our Price: £14.70

Product Code: 1-155-GWB

SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £11.45
Our Price: £6.58

Product Code: 1-155-BRK

Provides a 50mm gap between flue and wall and provides lateral support of the chimney along the wall. Not a loading bearing support.SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £27.75
Our Price: £14.57

Terminals

Product Code: 1-155-CL

Provides rain protection at the top of the stack. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £60.80
Our Price: £39.52

Product Code: 1-155-SC

Used in conjunction with a roof flashing it provides extra protection to the flashing. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £44.25
Our Price: £25.44

Accessories

Product Code: 1-155-D

SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £32.99
Our Price: £21.44

Product Code: 1-155-J

Provides a neat way of connecting pipes together. SW316-1mm Single Wall is suitable for use on appliacations fired by gas, oil and solid fuel with flue fas temperatures not exceeding 540oC, up to 750oC short firing.
Single Wall 1mm think stainless steel flue pipe is used to connect an appliance to either a chimney liner, stack or twin wall flue system. It can also be used to reline existing masonry chimneys. It is recommended that a verticle rise of 600mm should be allowed, immediately above the appliance before any change in direction. If bends are needed, then no part of a flue pipe should form an angle greater than 45° from the verticle, except where it may be necessary to use a very short horizontal section, not exceeding 150mm of flue to connect the flue pipe to a back outlet appliance. A maximum of 4 bends ( 2 offsets ) is permitted. Distances from combustible materials must be three times the diameter of the flue pipe. E.g. 150mm dm = 450mm clearance.
RRP: £11.73
Our Price: £7.39
© 2017 Flue Liner Direct - Google+